DL #1: The 9.2.2 universal OS installer CD's archive is a. MacDrive works with almost any type of disk including internal and external hard drives, CDs, DVDs, flash.Mac OS CPU Software 4.9, includes the Mac OS ROM file v9.2.1 Macintosh emulators are an attempt to 'emulate' Macintosh hardware on PCs, so as to enable them to run the Macintosh operating system.Suitable for G3 & G4 Macintosh models capable of booting from a Classic Mac OS via CD-ROM.So how does MacDrive work Plug a Mac disk into PC. That is where Macintosh emulators become important. Now comes the fun part - Is your CD-ROM drive compatible with A/UXAbout Emulators Normally, IBM-compatible PCs cannot run any Macintosh programs, or read Macintosh CD-ROMs and floppy disks.DL #3: Additional USB driver support for beige G3 only. If you install the Mac OS 9.2.2 that's here, onto this model eMac (possibly the eMac ATI 800MHz, also) then you should DL and use these drivers, too. This was perhaps the final production Macintosh able to boot native to a classic 9.x OS and its installed drivers were newer than whats on this universal install CD. DL #2: These are the ATI drivers as shipped with the G4 eMac 1.0 GHz with 8x combo drive, from 2003, (M8950LL/A). This archive has been tested as working, prior to uploading.
Cd Drive Emulator Archive Is APower Macintosh G3 (beige tower) 300MHz Confirmed working for these Mac PPC models: Check everymac.com for specs if you are unsure if your Mac is capable of booting to Mac OS 9.2.2 or earlier. This will install onto most early to late model G3 & G4 Macs.However if the Mac cannot boot into OS 9, e.g: Macs with USB 2.0, then this CD will not be of use (as a bootable System Install CD). G3 iMac (Summer 2000) 450MHz DV+ slot-loading with a G4 500MHz CPU (OC to 600MHz) G3 iMac (Summer 2000) 350MHz slot-loading, no FW/AP G3 iBook Translucent White (mid-2002) 700MHz, 16VRAM Office 2011 for mac opens in previewUsing an extracted System folder from the A1025 restore DVD, found here: Mac OS 9.2.2 System FoldersWith both of these methods, I still have this annoying wake from sleep problem on 9.2.2. Using the aforementioned “full install set” for the 867MHz/1GHz: Mac OS 9.2.2 & X 10.2.1 (PowerBook G4 Titanium 867MHz/1GHz) With regards to replacing the ROM file by using a more recent version of the ROM file which would have come with the Ti-book.Fortunately since that post, we now have the full original install sets for the following Ti models:The G4 Titanium DVI 667/800 and the G4 Titanium 867MHz/1GHz full install sets.So depending on your model, you can either grab and replace the ROM file from the correct set for your Ti, or do a clean install of Mac OS 9 using the original Ti-books OS install sets.And hopefully, this would fix any sleep problems noticed with the Ti and Mac OS 9.2.2.I have tried two methods of restoring my PowerBook G4 Titanium ( A1025), and both resulted with an inability to wake from sleep: I have had trouble with system sleep with mine…Perhaps with the G4 Titanium Book, it’s necessary to follow the hints in the post down below, made by “Doodle D Day” back in November, 2014. G4 Mirrored Drive Doors (2003) 1.25GHz FireWire 400If anybody DL's this and successfully installs it to a PPC Mac, or clone, please post which model Macintosh, so it can be added to the list of Macs above that this CD is confirmed to install to.New by MikeTomTom - 2020, May 25 - 3:36pmThe Ti book. G4 eMac ATI 8x combo (M8950LL/A) 1.0GHz Is there any way to get those buttons to display on my disk utility window? And how do I send a screen shot and attach it to show you what my Disk Utility window looks like?The Disk Utility toolbar (which houses the buttons) must have been toggled to off, somehow. That option is, I just found out, in a drop down list under "Image". I needed the adapter to be in “Master mode,” with the jumper removed from the adapter altogether.(As an aside: I figured there must be something wonky with either the adapter or the mSATA drive itself, because when I swapped in the old spinning HDD from a different PowerBook and did a clean install of 9.2.2, this PowerBook woke from sleep without issue.)There is no burn button on my Disk Utility. I decided to try and determine if the SSD was the problem.The IDE to mSATA adapter I used comes from the factory in “Cable Select mode,” with Pin47-Pin48 jumped together. (Should I not rule out hardware issues?) UpdateOkay, so I answered my own question. Other times, I see my desktop as it existed before entering sleep, with the cursor appearing as a wristwatch, and the control strip is just a blank white blob (with no responses to keyboard and mouse input).I considered hardware issues, as I’ve installed new RAM from OWC, as well as an IDE to mSATA adapter drive thing, but since there are no sleep issues in Mac OS X, I’ve ruled those out. The new versions of those programs, and current Cobalt, is over $3,000 plus you rent them instead of owning them.So, the decisions to spend a few hundred here and a few hundred there on what seems like an ancient system seems fairly logical especially given the "pop" that Cobalt has with a 1 GHz processor and a good video card on a large, "gasp" ViewSonic monitor cast off from the place where I used to work.Right now I am attempting to load MintPPC.I have had Ubuntu successfully installed on this machine. And all of the PowerPC versions of X can use it.I've gone to this trouble because I am running Ashlar Vellum Cobalt for OS 9 that I got for $300 - instead of $3,500 - when I was working as the Apple Sales Manager in a company in Wichita.Cobalt is a full-up parametric solid modelling CAD program and still compares very well with SolidWorks and the best programs from AutoDesk. This allow two screens, and again, OS 9.2.2. They show up as SCSI drives and OS 9.2.2 can use the drives quite nicely.The computer uses a Radeon ATI 9600 Mac Pro Edition video card. By going in through the PCI bus and by having ATA to SATA adapters, the LBA limitation on large IDE drives on Sawtooth Macs does not apply. I've not yet found a "give away" CAD workstation.By MikeTomTom - 2020, April 7 - Hi, and sorry: ".zip", quite right.It's not the downloaded ".zip" file that needs to be locked. But I can now print from my Linux/Mac.Probably "too much information", but I get yelled at for insisting on hanging on to an "ancient computer", when "you should just go out and buy a new computer", or "someone will just give you a computer". They bungled the USB interface for the Mac and the printer driver cannot connect with the printer under Macintosh, plus HP has removed all such drivers and the necessary update that did fix the USB interface.Linux does not support the scan function - I don't think.
0 Comments
Leave a Reply. |
AuthorBetty ArchivesCategories |